Auto parts tooling, injection moulding plastic parts

Auto parts tooling, injection moulding plastic parts

Service Details:

  • Brand:Kayou
  • Serial Number: M-0150
  • Country of Origin:Shenzhen, China
  • Certificate:ISO9001

Payment & Shipping Terms:

  • Price Quote:Negotiable
  • Minimum Order: 1
  • Average Delivery Time:25 days
  • Payment Method:T/T
  • Package Details:Wooden Case
  • Ability to Supply:5 Set/per month
Contact Us

Auto parts tooling, injection moulding plastic parts

Description

Auto parts tooling, injection moulding plastic parts

Bending guide rod parting core pulling mechanism

The structure principle of the bending guide rod parting core pulling mechanism is the same as that of the oblique guide rod side parting core pulling mechanism. Its obvious characteristics are that the bending guide rod is used, and the rectangular or approximate rectangular cross section of the guide rod is used to replace the circular cross section of the oblique guide rod. Therefore, this mechanism can also be used in many situations where inclined guide pillars can be used. Its advantage is that the inclined angle of the guide column is larger than that of the inclined guide column. Therefore, a larger oil drawing distance can be obtained in a shorter die opening or pushing. At the same time, the bending guide rod can be made into two bending forms, which can exchange smaller drawing speed for larger drawing force at the beginning, and obtain larger drawing speed with larger inclination angle after lifting the wrapping force, or make the bending guide rod and slider hole contact all the time without restricting and locking device, and use the straight part of the bending guide rod to obtain lagging core pulling. But the processing and assembling of the bending guide rod is much more difficult than that of the inclined guide rod, so it is not necessary to use the bending guide rod to pull the core in some cases where the inclined guide rod can be used. In order to simplify assembly and reduce die quality, bending guide rods are sometimes placed outside the template. Others, such as slider, chute, locking, limit and reset, reset first and so on, are the same as the oblique guide pillar. It should be noted that the clearance between the bent guide rod and the slider hole can not be too small, otherwise it may cause stuck phenomenon, and the general clearance should be greater than 0.5mm.

Two kinds of typical bending guide rod parting core-pulling dies are basically the same as the inclined guide rod, which can also be said to be a variation of the inclined guide rod. The bending guide rod is installed inside and outside the die. The middle hole has a large encapsulation force on the core, and the inclination is not allowed, the demoulding force is large, and the sleeve demoulding is not very good, so the bending guide rod side core pulling is adopted. When the die is opened, the bending guide rod has a straight part, which is empty for a certain distance. In this distance, the slider is locked by the bending guide rod and can not move, and the plastic part is basically detached from the core without deformation under the clamp of the slider. Then continue to open the mould, the inclined part of the bending guide rod drives the slider to complete side core pulling, so that the plastic parts can be demoulded smoothly.

 

 

 

Plastic Injection Mold Show

Auto parts toolingmouldinjection moldinjection moldinjection moldinginjection moldingplastic injection moldplastic injection mouldplastic injection moulding

 

 

 

Plastic Part Show

plastic injection moldingplastic injection mouldingplastic part injection moldplastic part injection moldingplastic part injection mouldplastic part injection mouldplastic part injection mouldingplastic injection mold productplastic injection mold product

 

 

 

Factory Show

plastic injection molding productplastic injection moulding productinjection moulding productioninjection molding productioninjection mould productioninjection mold productioninjection plastic moldinjection plastic mouldinjection plastic molding

 

Auto parts tooling, injection moulding plastic parts

 

Related Services:

Get in Touch with us

Still have Questions

Our Headquarters

Work Time :
8:30-18:00(Beijing time)
FAX :
86-7552-3156569
Business Phone :
86-7552-3156569(Working time)
Factory Address :
E bulding 220th Reixing industrial Park XingYe Road Wusha ChangAn GuangDong provice China

Send Us an Email

contact us